Ccna basic router configuration pdf

While in global configuration mode enter. They are virtual, in the sense that they are a function of software — there is no hardware associated with them. To set the Telnet password type:. The first useable IP address of the While in global configuration command mode type.

To test connectivity between routers Ranet A and Ranet B we will execute a ping command. The list of commands below are an example of how you can type all the router commands into a plain text file and paste it into the router CLI.

Be sure to order them correctly and remember which command mode you are in. Now that you have completed the configuration of the router, test your work. Target Audience Anyone desires a practical, technical introduction to the field of networking.

High-school, community college, and lifelong-learning students interested in careers as network technicians, network engineers, network administrators, and network help-desk staff. In addition, instruction and training are provided in the proper care, maintenance, and use of networking software, tools, and equipment and all local, state, and federal safety, building, and environmental codes and regulations.

Course Objectives The CCNA certification indicates knowledge of networking for the small-office, home-office SOHO market and the ability to work in small businesses or organizations whose networks have fewer than nodes. Approximately 35 hours will be designated to lab activities and 35 hours on curriculum content. A case study on structured cabling is required, but format and timing are determined by the Local Academy. What has changed from CCNA versions 2.

Course Outline Module 1. Introduction to Networking Overview 1. I will walk you through all of the commands to accomplish each objective of this lab. Before we get started, I will explain how to configure routers in the Packet Tracer lab environment. The way this lab has been setup resembles how you would configure a router in actuality.

You must use the PC to open a terminal console session to the router in order to configure it via the command line interface CLI. This is the PC that has a console light blue cable connected to the router that will be configured. Your prompt will show the router name followed by a greater than sign. Remember that pressing the enter key will tell the router to execute the command you have typed.

The router name is now followed by a pound symbol to show this. This will save you lots off typing although it is not always necessary to have each word in a command completely spelled out. HINT: Use the question mark? It will show you which of all the available commands are for the command mode you are in.

You can use it after typing a few letters of a word or after one or two words of a command. We are now prepared to enter the commands to complete the lab. You are the Network Administrator at Ranet. We have just installed a new router to be our gateway. After configuring this, you should be able to 1. Ping to This password will be required to enter privileged EXEC command mode.

This password will deter unauthorized access to the router via the console connection. While in global configuration mode enter. They are virtual, in the sense that they are a function of software — there is no hardware associated with them. To set the Telnet password type:. Router configure terminal Enter configuration commands, one per line. Router config Step 4: Configure the router name as R1.

When we think of connectivity in a network, the router is probably the first device that comes to mind, but switches play a vital role in enabling network devices to communicate. You also want to check the physical state of the device and verify that none of the cables are damaged. If for any reason putty is not an option for your setup, you can get similar results with a PuTTY alternative. To start configuration, you want to connect the switch console to PuTTY.

You can do this by doing the following:. You can make the switch easier to locate in the network by assigning a hostname. Cisco All Commands Pdf Attention reader! Explore career certification paths below that meet your professional development goals. Use of a term in this book should not be regarded as affecting the validity of any trademark or service mark. The show vlan command always lists all VLANs known to the switch, but the show running-config command does not. Troubleshooting Commands When problems arise on Cisco devices, there are a number of show commands you can use to help identify what the problem is.

Becoming proficient with the Cisco IOS means learning some essential commands. This quick reference describes 10 commands you'll need to rely on when handling various configuration and troubleshooting tasks.

It may seem entirely too obvious that you should know how to type? However, the Cisco IOS is completely different from other operating systems when it comes to using the question mark help key. As the IOS is a command-line operating system with thousands of possible commands and parameters, using the? The guide summarizes all CCNA certification-level Cisco IOS Software commands, keywords, command arguments, and associated prompts, providing you with tips and examples of how to apply the commands to real-world scenarios.

This prevents the name resolution attempts that occur if you mistype an IOS command.